The Silicone O-ring is commonly used in sealing applications requiring flexible performance at different temperatures. But picking the right seal is about more than just finding a silicone O-ring because if the incorrect material hardness, size, or material is chosen, leakage and early failure could occur along with expensive replacements.
Here are four important things to consider before ordering your silicone O-rings:Compatibility with temperature and chemicals, the material hardness and compression set, and the need for medical grade.
We'll discuss what you'll need to look for before picking out the right Silicone O-ring and what kind of information to provide when getting a quote.
If there is a need for a flexible seal over a wide range of temperatures or one that has to withstand outdoor exposure such as exposure to ozone and weathering, then silicone rubber will generally come into consideration. This would be especially true in instances where conventional rubber may have a tendency to become too hard at low temperatures or otherwise lose desirable qualities due to high temperatures.
It must be understood however that "silicone" is only a generic designation rather than a specification. The performances of these various silicone materials can vary and the temperature ratings of one compound cannot justly be extrapolated to a new one and maximum performances seen under laboratory conditions do not translate directly into service life under actual use.
Sometimes, there is no point in applying silicone because certain oils, fuels, chemicals, and greases may affect the performance of this rubber material, depending on the specific type of silicone used. Rubbing and wear may also serve as another criterion in choosing an alternative to silicone.
The exact substance which is going to come into contact with rubber, its concentration and temperature should be known in order to choose silicone O-rings. In case of working with petroleum oils and fuels or dynamic applications, the properties of silicone rubber should be compared with those of its rivals.
When in doubt about the specific conditions, it is necessary to request a supplier to carry out the analysis of the application and provide the corresponding data. An elastomer cannot be chosen just by its temperature range.
Since soft silicone o-rings can be more easily deformed during compression, it can also be more easily shaped around a sealing surface in certain O-ring seals. Nevertheless, a mere softness cannot guarantee the reliability of the seal. In case of the material being too soft in comparison to the design, the pressure or clearance between the parts can lead to an undesirable deformation of the ring. Similarly, a harder ring does not guarantee a better seal since its deformation requires more effort to be applied.
For consumers, the relevant issue is not “Do you have a soft O-ring?” but “What level of hardness would be appropriate for this particular O-ring groove and pressure?” The hardness of the O-ring is measured on the Shore A scale.
The O-ring will be compressed while being installed to make contact with its surroundings. Over time, high temperatures and constant pressure can lead to a decreased ability to return to the previous state. This phenomenon is called the compression set. In case the amount of elastic recovery of the O-ring is significantly reduced, it will fail to establish proper contact.
This is why a low initial cost or a soft touch is not necessarily a guarantee of good sealing. Buyers should inquire whether the material data or test results can be provided. The latter will be useful only if the temperature, time, testing method, and the grade of the material are stated.
The internal diameter and the cross section of the O-ring should be in accordance with the design. The dimensions of the groove and the compression level are other factors that play an important role in the sealing process. An O-ring which is too small, too large, or is compressed wrongly can cause leakage and premature wear.
In case you want to replace your existing O-ring, provide the manufacturer with a measured picture or the technical drawing rather than just the photograph. In case you are designing a new system, give him the groove dimensions, the desired hardness level, the pressure level, the temperature and the material in contact.
Before producing the item in bulk, make sure that the approved prototype fits the assembly.
There can be a variety of contact conditions in the case of medical devices. It could be that the seal does not have any physical contact with the patient but exists only inside the device, or it may come into contact with a flow of fluid, or even the seal may have some physical contact or indirect contact with the body. This is why the use of term “medical silicone” is just a starting point of a conversation.
Being "medical grade silicone" does not mean that medical silicone o-rings can be used on all kinds of medical devices. This will vary depending on the role of the component, its contact and with what, and the design of the final product.
Before ordering, inform your supplier about the type of contact – either with the body, bodily fluids, a fluid path, or just the internal components of the device. Inform him also about the planned cleaning or sterilization process.
Asks for supporting documents that correspond specifically to your grade of material and the particular component that you want. In some cases, this will include material specification, test results, and traceability documentation. Do not assume that a document for silicone tubing or raw silicone material is enough.
You need to verify that the material and component you intend to use have all the necessary information.
To help a manufacturer assess your requirements, include as much of the following information as possible:
●Dimensions: Inside diameter, cross-section, and a technical drawing if available.
●Material requirements: Silicone grade and target Shore A hardness, if specified.
●Operating conditions: Working temperature, pressure, and the fluid or substance that will contact the seal.
●Application: Whether the O-ring is used in a static or dynamic assembly.
●Order details: Estimated quantity, sample requirements, and expected production schedule.
●Documentation: Any applicable test reports, material records, or customer-specific requirements.
In case you do not have a complete drawing, give the details that you know, such as the dimensions, a physical sample, or application description. This way, the supplier will analyze what is available and determine the specifications that still require confirmation.
When making your production order, ensure that all the following items have been agreed upon.
For a custom component, inquire about how the sample will be examined, and what parameters/attributes will be measured prior to mass manufacturing. Determine the drawing revision, material identification, inspection specifications, and documentation requirements if required. If traceability and batch documentation is essential in your industry, verify this information prior to placing your order.
The sample inspection cannot be a mere visual check. The sample must be able to perform satisfactorily in its assembly application as well as in terms of performance in service. In some cases, testing will need to be performed under service conditions.
When considering custom silicone O-ring manufacturers, consider factors other than the unit price such as the manufacturer's ability to examine your drawing, talk about your material needs, provide you with samples, and ensure that your specifications are met before manufacture.
Ruixiang provides silicone seal rings as well as custom silicone products. As per the information provided by the company regarding its products, silicone seal rings can be customized depending on the customer's drawings or samples.
In case you want to customize silicone seal rings for use in your new or old component, provide your drawing or sample, the required dimensions, conditions of use, and expected order quantity to the manufacturer. It will help the manufacturer evaluate your requirements and discuss further.
Q1.What are silicone O-rings commonly used for?
They are used in many sealing applications where silicone’s flexibility and temperature performance are useful. Suitability depends on the actual design and operating conditions.
Q2.Are silicone O-rings suitable for high temperatures?
Some silicone compounds perform well at elevated temperatures, but the allowable range depends on the exact formulation, exposure time, and operating environment.
Q3.Are soft silicone O-rings better for sealing?
Not always. Hardness should match the groove, compression, pressure, and whether the seal moves during operation.
Q4.Can silicone O-rings resist oils and chemicals?
Compatibility varies by compound and fluid. Confirm the exact medium, concentration, temperature, and contact duration before selecting a material.
Selecting an appropriate O-ring made of silicone goes beyond verifying the heat resistance and hardness that buyers prefer. It is necessary to think about the dimensions, material compatibility, compression, operational environment, and the proof needed for the application.
In case of a custom order, making drawings and samples of the product together with giving detailed information on the environment in which it will be used may facilitate the process of understanding requirements prior to manufacturing.
In case of purchasing custom silicone O-rings, refer to the silicone seal ring page of Ruixiang.